FSEast DV 2019
FSEast DV 2019 Engineering Design Quiz
Test your knowledge on the Engineering Design Event at FSEast 2019! This quiz covers various aspects of the event, including rules, vehicle dynamics, materials, and cost reports.
- Challenge your understanding of engineering principles.
- Learn about vehicle performance metrics.
- Engage with fellow engineering enthusiasts.
Can a team be eliminated from the Engineering Design Event by the judges, if every document of theirs was accepted and they are present at the Engineering Design Event?
Yes, if the judges consider the vehicle to be in unfinished state.
No, if a team is present at the event, the judges are obligated to evaluate their performance.
Yes, if the team did not pass any scrutineering prior.
Yes, if the judges consider the number of the team members present at the discussion insufficient.
Which of the following dynamic disciplines will be organized first time in 2019 at FS East?
Driverless AutoX Event
Trackdrive Event
Driverless Skidpad Event
AutoX Event
In which Cost Report Document does the team need to list the research and developement costs?
In the DBOM
In neither of the Cost Report Documents
In the Cost Explanation File
In the CBOM
The circular Dynamic Platform at ZalaZone has 1% of slope from North to South. The diameter of the Platform is 300 m. If a ball is released on the highest point of the Platform (North), from standstill state, what will be the speed of the ball at the lowest point of the Platform (South)? Consider that the ball rolls directly from the highest point to the lowest point. Rolling resistance is 0 Mass of the ball is 200g G = 10 m/s²
5,897 km/h
7,7459 m/s
7,7459 km/h
5,897 m/s
If a thin and infinitely long fibre's diameter is reduced, which of its properties from the following will increase?
Peak force at failure
Strength
Young modulus
Stiffness
Our vehicle completes the Acceleration Event. Its velocity is 126km/h, when it crosses the finish line. How much time did it need to complete the run, if we assume, that its acceleration is constant during the run?
4,28s
3,86s
4,56s
4s
A car finishes the skidpad event with an average laptime of 5,0 seconds. The static friction coefficient of the ground and the tire is 0,9. What was the aerodynamic downforce to weight ratio during the run? Assume, that the car is travelling on the centerline of the track. G=9,81 m/s²
0,5
0,45
0,9
1,35
Which of the following requirements is a must for all types of vehicles, when moving the vehicle on the competition site other than on the practice or competition tracks?
Detached master switch.
A registered driver wearing the required driver equipment as defined in T 13.3 except for helmet, arm restraints and balaclava having full control of steering and braking
Two team members walking on either side of the vehicle.
Vehicles must be pushed at a normal walking pace by means of a red pushbar, equipped with a fire extingusher.
Which of the listed material can be described with the following fictional mechanical properties? Specific strength (σ[MPa]/ϝ[g/cm³]) = 1656 Specific modulus (σ[GPa]/ϝ[g/cm³]) = 57 Failure Strain (%) = 1,8
Titanium
Aramid Fiber Reinforced Polymer
Steel
Carbon Fiber Reinforced Polymer
According to the FS Rules 2019, how many points will a team score eventually on the Cost and Manufacturing Event, if the team is not in the final, the score awarded to a team during the initial judging is 79 points, while the highest score awarded to any team not participating in the finals is 91 points?(
95
82,5
79
86,8
Which is NOT a mandatory mission in the autonomous system?
Trackdrive
Inspection
EBS test
Manual driving
Test track
What does the yellow and red striped flag mean during Endurance and Autocross Event?
The driver must pull into the driver change area for discussion with the officials concerning an incident. A time penalty may be assessed.
Mechanical black flag. The driver must pull into the driver change area for a mechanical inspection of the vehicle, something has been observed that requires a closer inspection.
The track is slippery or something is on the racing surface that should not be there. The driver must be prepared for evasive maneuvers to avoid the situation.
The track is slippery or something is on the racing surface that should not be there. The driver must be prepared for evasive maneuvers to avoid the situation.
{"name":"FSEast DV 2019", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your knowledge on the Engineering Design Event at FSEast 2019! This quiz covers various aspects of the event, including rules, vehicle dynamics, materials, and cost reports.Challenge your understanding of engineering principles.Learn about vehicle performance metrics.Engage with fellow engineering enthusiasts.","img":"https:/images/course4.png"}
More Quizzes
Make your own Survey
- it's free to start.
- it's free to start.