Rvrbrbrvrb

Nuclear items are identified by the material management code

Which parts or components are funded, procured, and owned by the Air Force?

Which parts or components are furnished to the Air Force but remain the property of Department of Energy (DOE) regardless of custody?

The "X" in the expendability, recoverability, repairability, category (ERRC) code "XB3" means the item is

What agency controls the unit spares authorization list items?

If units require a change to authorized unit spares authorization list items?

Who develops and published local procedures to ensure proper control, protection, accountability, and reporting of weapons, major assemblies, and related components

Which procedure is not performed during the stockpile emergency verification (SEV)?

Phase 1 actions of a stockpile emergency verification (SEV) can be a physical verification or

How often does the Defense Threat Reduction Agency (DTRA) provide field units location inventory listings?

The location inventory listing (LIL) is extracted from the consolidated nuclear weapons database at

Which actions do not require you to update the location inventory listing (LIL)?

Who has temporary custody of the weapons and grants access to the immediate area where the weapons are located?

Taking control of a weapon from another individual or relinquishing control of the weapon to another person is known as

What form does the transporting and mating supervisor sign to accept custody of a Minuteman III reentry system (RS)?

For reentry system (RS) custody transfer, who prepares an original and one copy of the Air Force (AF) Form 504, Weapons Custody Transfer Document, leaving the individual signature blocks blank?

After delivering the weapons to the alert aircraft, what does the driver mark on the work order?

What must be done to nuclear weapons before they can be loaded to another aircraft after they are downloaded?

The maintenance team chief who is responsible for final assembly must prepare and sign the buildup sheet. Who must physically verify the serial numbers and configuration and certify them by signing the buildup sheet?

Who submits monthly nuclear ordnance shipping schedule (NOSS) forecasts to the Nuclear Control Point (NCP)?

Which document do we use to update accountable transactions in Defense Integration and Management of Nuclear Data Systems (DIAMONDS)?

Whose signature certifies the expenditure statement, for test items expended during stockpile flight testing or other operational test and evaluation testing, on expenditure documents?

How do you transport the W80 warhead on a MHU-141/M munitions handling trailer?

Who is responsible for accepting custody of nuclear cargo that has been positioned for loading?

What size suspension system carries the B61 weapon system?

Which two assemblies make up the B83 weapon sytem?

Which section of the B83 weapon system provides shock mitigation during delivery?

Which handling gear (H-gear) is used to store, transport, and hold the B83 gravity weapon system during maintenance?

When inspecting the external surfaces of a bomb, which type of markings is compromised of chock bands, center of gravity, and match marks?

When inspecting a bomb for damage, which condition is not considered an acceptable manufacturing defect?

Which of the following is not part of preparing a bomb for strike?

When can you perform command disablement system (CDS) on war reserve (WR) weapons?

Which tool may be used as part of the non-violent disablement procedure for a nuclear weapon?

When, if ever, would you unpack weapon components and cables from the H1127 storage bag for inspection procedures?

When inspecting bomb handling equipment, what is the correct procedure upon finding a cracked threaded shank eyebolt on a H1125A bomb hand truck (BHT)?

When inspecting bomb handling equipment, which criteria would make the H1125A/H1671 handling equipment unserviceable?

What is an inspection point of the H1242 swivel caster assembly?

What must you check immediately after lifting a bomb using a H1004 bomb-hoisting adapter and hoist?

How are the swing bolts of the H1125A/H1671 top cradle torqued?

After lowering the B61 on the H1229 maintenance stand, what must you do before closing the cradle bands?

When you use the H1354 machine-screw removal tool to remove the last screw from a B61 subassembly during disassembly, you should install

Which items would you use to remove a stuck bomb radar nose of a B61?

The case-separation limiter on the B61 only works if the

When connecting the gas generator on the B61, you equalize your body potential by touching

After mating the B61 subassemblies, install the top three high-torque screws and torque them to

Which type(s) of equipment is/are authorized to lift a double-stack of B83s?

Which type of maintenance does the Secure Transportable Maintenance System (STMS) provide?

The W80 warhead is equipped with a

What piece of equipment is primarily used to install and remove the W80 warhead payload to and from the H1388 shipping and storage container?

The MHU-89/E work stand includes all the following except

What is an acceptable location to perform a full external surface inspection on a W80 warhead?

Which component is not a part of the H1388 shipping and storage container?

To remove the warhead with the H1387A strongback, attach the lifting device to

What other equipment do you use with the T557 digital thermometer to determine the condition of the reservoir during a W80 warhead limited life component exchange (LLCE)?

How are air-launched cruise missile (ALCM) and MHU-159/E guided missile handling unit secured to the MHU-141/M munitions handling trailer for payload mate and demate?

What air-launched cruise missile (ALCM) configuration gives the missile a maximum width of 24 inches?

The two methods used on the air-launched cruise missile (ALCM) to extend the inlet body during launch are a mechanical backup and

Which air-launched cruise missile (ALCM) payload bay door feature allows you to see if a payload is installed?

What interfaces between the MHU-186/E guided missile hoisting beam and a missile with an ejector installed?

The CVU-143/E umbilical receptacle protective cover protects the umbilical receptacle from

What is the function of the MXU-691/E control surfaces missile ground safety lock?

When do you perform missile safe status checks?

Nuclear hardness of the pylon is maintained when personnel

What provides easy access to the aft pylon support fitting?

Electrical and pneumatic missile connections on the pylon are made through the

How many swing arms support the entire weight of the pylon and are retractable for pylon removal?

What is attached to the pylon and acts like a "ball socket" that receives the "ball joint" from the pylon loader adapter (PLA) swing arm?

Which part of the aircraft guided missile and bomb rotary launcher (AGMBRL)/common strategic rotary launcher (CSRL) provides mechanical and structural support for the aircraft and suspended loading and checkout frame (SLCF)?

How many arming solenoids are incorporated into the ejector?

The reentry vehicle (RV) is designed to perform all of the following functions except

What design of the reentry vehicle (RV) overcomes the intense heat generated by reentry?

A material for the reentry vehicle (RV) heat shield is made of is

The reentry vehicle (RV) overheating at reentry is prevented by the "sloughing" off. What does "sloughing" mean?

Which section of the MK21A reentry vehicle (RV) houses the high impulse transducer (HIT)?

Which reentry vehicle's (RV) section houses the W78 warhead (WH)?

Which component is part of the MK12A reentry vehicle's (RV) aft section?

You use the MHU-170/E guided missile warhead section lift truck when installing or removing payload to and from an

The MK21 reentry vehicle (RV) is divided into how many major parts or sections?

Which inspection, if any, is performed after a verification inspection on a reentry vehicle (RV) is completed?

What size safety wire is used to secure the electronic inspection record card (eIRC) packaged in a waterproof envelope to the reentry vehicle's (RV) shipping and storage container (i.e., H1224A or H1473)?

After you inspect the high impulse transducer (HIT) cable in the MK21A reentry vehicle (RV) forward section, you find a broken safety wire. What should you do next?

What should your next step be when you find a broken safety wire in the MK21A reentry vehicle's (RV) mid section during inspection?

How many times during a recycle can you lightly sand a contaminated area of the reentry vehicle (RV) carbon-phenolic material?

If a replacement breech joint setscrew fails to move with 5-inch pounds (in-lb) of applied torque, what action do you take?

When you perform hardness critical procedures (HCP), identifies as **HCP** in the technical order (TO), you must

What is the only authorized shipping and storage container for shipping the W78 warhead (WH)?

When installing the W78 warhead (mid section) in the reentry vehicle (RV) maintenance stand, you know it is positioned correctly when the

When installing the warhead (WH) in the MK21A reentry vehicle (RV) maintenance stand, you create a friction load between the mid section and the cradle by

What part of the reentry vehicle (RV) hoisting adapter do you use for lifting and transferring the MK21A RV?

After you assemble two MK12A reentry vehicle (RV) sections, the breech joint is acceptable if you cannot insert the feeler gauge more than 0.5 inches in how many consecutive locations?

Which component is not part of the reentry system (RS) installation kit?

Which stand supports the MK12A reentry vehicle (RV) during installation and removal of the reentry system (RS) installation kit?

The elaborate torque procedure for the zero impulse bolts (ZIB) serves several necessary purposes. Which option is not one of them?

During an electrical checkout, what should a technician do when cables are left disconnected from a test set because of a new cabling diagram?

What should you do if a malfunction occurs during a stray voltage test of the forward section?

During the checkout of cable W3A, how is the ARM/MATE nut tightened on the P3 of the W4145 cable?

What is the rejection criterion for the W87 body section when you inspect the internal forward edge for delamination and/or chips that affect the bond line?

When inspecting the W87 body section, what is a reason to reject the heat shield plugholes?

When inspecting the W87 body section, which option is a reason to reject the radio frequency subsystem (RFSS) cables located in the interior of the W87 aft section?

What is the only authorized shipping and storage container for shipping the W87 warhead (WH)?

What do you use to cover the fuse support shield once you remove the warhead electrical system (WES) cap?

What equipment attaches to the facility hoist and the MK21 reentry vehicle (RV) forward section for handling operations?

What do you install to hold the reentry vehicle (RV) maintenance stand cradle in the open position before you place a RV in the stand?

During reentry vehicle (RV) disassembly, where must you install the MK21 RV before you remove cable W4A?

Once the ball-lock restraining tool is removed during reentry vehicle (RV) disassembly, what is inserted into the cartridge port?

When disassembling the reentry vehicle (RV), before you lift the forward section from the body section, you must rotate it until

When assembling the MK21 reentry vehicle (RV), what must you turn 90 degrees on the arming and fuzing assembly (AFA) mating base fixture before you install the fixture on the body section?

How do you verify alignment when torquing the forward section on the MK21 reentry vehicle (RV) during assembly?

During MK21 reentry vehicle (RV) assembly, what secures the rear cover of the RV to the body section?

You locate the W4A cable to install on the MK21 reentry vehicle (RV) during assembly by identifying the

The humidity indicator plug on the H1473 shipping and storage container indicates excessive moisture inside the container by turning

If units do not receive nuclear ordnance controlled material items by the estimated delivery date for backordered items, the nuclear accountability and reporting section (NARS) follows up with Nuclear Security Campus (NSC) personnel at leat

Who processes the Air Force (AF) Form 2005, Issue/Turn-in Request?

After receiving incoming classified property, when do you physically inspect it?

For outside the continental United States (OCONUS) shipments, start follow-up action if you do not receive a signed Department of Defense (DD) Form 1348-1A, Issue Release/Receipt Document, within how many days?

Who is responsible for preparing the Department of Defense (DD) Form 1911, Material Courier Receipt?

Who signs the Air Force (AF) Form 2005, Issue/Turn-in Request, upon issue or turn in of property?

Do not issue Group-X kits

What form do you use to turn in items that are found-on-base (FOB)?

When cleaning excess lubricant from mounting holes on the B61 after assembly, you should use

Which technical order (TO) do you use to handle, protect, and inspect electrical connectors when procedures are not contained in the weapon-specific TO?

What must you do if you are rotating a H1229A maintenance stand and the bomb radar nose is still attached to the bomb?

Which piece of equipment do you use to monitor tritium gas during limited-life component (LLC) exchanges?

To remove the H1097A storage bag from the B83, you disengage the

What is the next action you take upon finding separation of rubber from the wheel hub of the H1347/H1347A bomb handling equipment?

When inspecting the H1347/H1347A bomb handling truck, which situation is acceptable?

Which test equipment do we use to determine if the limited life component (LLC) has been fired for the B83?

A pair of tapes on a B83 bomb consists of two tapes marked with

When removing the aft assembly, which pair of B83 tapes do you remove first?

What is the maximum pounds per square inch gauge (psig) of air pressure used for removing B83 tapes?

After you remove the tapes from the B83, how do you store them for reuse?

During a B83 reassembly, when do you perform the T304C continuity test(s)?

Which B83 tapes do you install first?

When installing B83 tapes, if the tip of the H1452 tape driver comes up against the end of the case slot before the tape is fully seated what should you do?

What connects in line with the components cooling unit (CCU) and is used to check the operations of the bypass valves?

Before mating missiles, the pylon requires a periodic inspection every

The bearing that allows the launcher to rotate is part of the

What is the purpose of the nitrogen-charging adapter set?

Which areas are not inspected when inspecting a launcher loader adapter (LLA)?

When preparing a launcher for shipment, you are not required to

What position is the shut-off valve of the nuclear station logistic unit (NucSLU) in for missiles?

Which assembly is not a major component of the ejector rack?

What regulates the ejection force of each ejector piston of the aircraft/bomb ejector rack assemblies?

On the reentry system (RS), what supports the reentry vehicles (RV)?

During the initial launch, what protects the warheads (WH) until the reentry system (RS) reaches the outermost stmosphere?

Where is the rocket motor located in the reentry system (RS)?

What is the purpose of the V-band clamp?

If a thermal panel on the inside of the aft shroud is still loose after torquing, you must

If while inspecting the W6A cable on the reentry system (RS) you find damage to the sleeving which also involves damage to the wire insulation underneath, what do you do?

On the reentry system (RS), how is one 180-degree section of the shroud release shield removed during aft shroud removal

The V-band clamp on the reentry system (RS) is preloaded with how many pounds?

When removing the chaff dispenser, approximately how many inches do you pull the dispenser retainer so the rear uniball fitting disengages the bulkhead rear fitting pins?

Before handling, connecting, or disconnecting RS electrical equipment, you must immediately

The parameters the reentry system test set (RSTS) measures are

When testing the arm and disarm (A&D) device using the reentry system test set (RSTS), what indication do you look for when the safing pin is installed?

When performing a fault isolation procedure using the explosive set circuitry test set (ECSTS), what steps do you perform if the test results indicate greater than 5.0 ohms (Ω)?

When performing a fault isolation procedure using the explosive set circuitry test set (ECSTS), what steps do you perform if the test results indicate less than 5.0 ohms (Ω)?

When installing the V-band, how do technicians apply torque to the self-aligning nuts on each V-band thruster bolt?

To transfer the reentry system (RS) to the munitions facility pit, use an overhead hoist and the

Before transferring a forward shroud on a pallet, how do you secure the upper support ring to the forward shroud pallet?

When transferring the payload support, how do you fasten it to the aft element support plate?

Which component provides electrical and mechanical interface between the reentry vehicle (RV) and the deployment module (DM)

When are you required to test and monitor for toxic air within the Weapon Storage and Security System? (WS3)?

Which option is not a component of the Secure Transportable Maintenance System (STMS)?

How are the ejector rack pylon interface (PI) fittings used?

What orifice designation is used with the air-launched cruise missile (ALCM) ejector?

If the cartridge retainers on the ejector assembly are safety wired, this tells you

Which ejector rack is the only device we use to attach an air-launched cruise missile (ALCM) to a pylon?

Which procedure is not part of final ejector rack installation

Which cartridges do you use in the air-launched cruise missile (ALCM) ejector?

The easiest pylon positions to mate are centerline, located at position

When inspecting the umbilical radio frequency interface (RFI) rings, replace the umbilical if

When mating an air-launched cruise missile (ALCM) to a pylon shoulder position, what must you install on the handling unit?

To secure the launcher in the suspended loading and checkout frame (SLCF), rotate the forward and aft downlock drives until the indicators show

Who is responsible for preparing command disable system (CDS) codes when shipping CDS equipped weapons and what is the classification of these codes?

The electrical operating system that fully opens the Weapon Storage and Security System (WS3) vault in approximately 3 minutes describes which operating system?

You should use the Weapon Storage and Security System (WS3) alternate operating system when

Which Weapon Storage and Security System (WS3) vault control control group component contains two recode module receptacles for entering unlock codes during recode operations?

Who controls the keys to the locks used for lockout operations?

How are tags attached to energized equipment or energy sources if that equipment is not to be used?

Which space is not a confined space?

Which Weapon Storage and Security System (WS3) component provides periodic polling of the vaults to check their operation and the status of the communications link?

In the event of a power failure, the uninterruptible power system (UPS) supplies equipment and console power for at least how many hours?

The authority to modify identification numbers and time delay (ID-TD) data for opening of the Weapon Storage and Security System (WS3) is given by the

Which Weapon Storage and Security System (WS3) vault control group component operates the vault's primary operating system?

Which Weapon Storage and Security System (WS3) vault assembly component contains sensors that detect water accumulation and earth movement?

How do you secure the missile-handling unit to the lift truck table manipulator head during missile transfer?

To what position do you set the suspended loading and checkout frame (SLCF) directional control valve for launcher rotation with a power drive unit controller (PDUC)?

On the munitions handling trailer (MHT), how many attaching fittings per lift beam are used at any one time?

You use manual pumps on the munitions handling trailer (MHT)

How does the service brake system on the MHU-141/M munitions handling trailer operate?

When transporting B83s on a 40-foot trailer, when (if ever) is blocking used?

Which lift truck component holds the load level during lifting operations?

How many pounds is the lift capacity of the MHU-83B/E gasoline-powered, self-propelled hydraulic lift truck?

The maximum jammer speed of the MHU-174/E electric-powered, self propelled hydraulic lift truck when loaded is

How many minutes should you allow the lift truck engine to warm up to reach the optimum running temperature?

Before starting a gasoline or diesel lift truck engine during extremely cold weather, you may need to

On diesel lift trucks, remove air in the fuel lines by using which pump?

During the loading process, the pylon is secured to the suspended loading and checkout frame (SLCF) with

On the pylon loader adapter (PLA), how are the swing arms positioned when performing pylon post-load procedures?

How do you retract the hook on the launcher loader adapter (LLA)?

During preloading, before positioning the pylon under the suspended loading and checkout frame (SLCF), make sure the

The forward pendulum and fixed attachment fittings are installed in which position on the MHU-196/M munitions handling trailer for launcher loader adapter (LLA) mate?

What piece of equipment allows you to position a missile at an angle for a pylon shoulder position mate?

When connecting the umbilical connector to the missile, how do you know the engaging nut is fully seated?

What do you do if the locking collar does not drop after you torque the attach bolt to 800 inch-pounds (in-lb. ) during a missile mate to a pylon?

Which item is not part of ejector preparation for a gravity weapon mate to launcher?

During pylon interface (PI) fitting installation on the ejector for the launcher mate, if you can't install the cotter pin after 20 inch-pound (in-lb. ) torque,

How do you tighten the sway brace pads for the B61?

To measure and detect toxic air levels within the Weapon Storage and Security System (WS3), you would use which piece of equipment?

During normal operations, the toxic air test set indicator draws continuous air samples through probe and hose assemblies into

What is the maximum capacity of the Secure Transportable Maintenance System (STMS) lifting systems?

When preparing to load the launcher into the suspended loading and checkout frame (SLCF), the launcher spline key must be in the index or

What position must the frame power drive controller (FPDC) indicate before you can remove the launcher from the suspended loading and checkout frame (SLCF)?

When removing the launcher from the suspended loading and checkout frame (SLCF), raise the launcher loader adapter from the suspended loader adapter (LLA) until the LLA yokes are approximately

Once a nuclear weapon reaches the last transfer point, who is responsible for its security?

Which items require shoring when being tied down in a safeguards transporter (SGT)?

What is the minimum spacing (center-to-center) for tie-down lugs in the safeguards transporter (SGT)?

During transportation on the MHU-141/M munitions handling trailer with rail sets installed, where must the payload(s) be located

The military first destination (MFD) is the first military base that

A weapon container not intended for towing is rated as

How is the receipt or shipment of classified nuclear material done and verified for an airborne logistic movement, and by whom is it done?

Units do not coordinate forecasted logistics movements with which agency?

Which agency is responsible for shipping limited life components (LLC) in H1616 containers?

Which unlock codes do each set of recode modules store?

Which code modules stores and transfers a complete set of encoding keys to authentication units, sensor processors, and data authenticators?

You will use the reserve set of rekey modules if the

What is the main purpose of lockout/tagout procedures on a Weapon Storage and Security System (WS3)?

Where can you find lockout/tagout procedures on a Weapon Storage and Security System (WS3)

Which space is not a confined space?

When is a cross-load operational readiness inspection performed on a launcher?

You close hooks of the ejector rack when mating a bomb to the launcher by turning the

Approximately, how far do you lower the lift truck from the bomb after the ejector hooks are closed and you see the safing mechanism installed for a bomb mate to the rotary launching assembly (RLA)?

When installing cartridges in the ejector, do all of the following except

When do we perform the post download operational readiness inspection on a launcher?

When using the gravity weapon loading adapter for a B61 mate operation, how do you position the gravity weapon loading adapter support blocks?

How many different methods can you use to install or remove the BRU-44/A ejector rack to or from the rotary launcher assembly (RLA)

What ejector cartridges are used with the BRU-44/A ejector rack?

What do you use to rotate the launcher if you cannot rotate it with the power drive unit controller (PDUC)?

Which post-use inspection procedure do you not do on the MHU-141/M munitions handling trailer during extremely cold weather?

What is the maximum load capacity on the MHU-196/M and MHU-204/M munitions handling trailers (MHT)?

During the munitions handling trailer (MHT) towing operations, a fixed mechanical stop limits the front wheel bogies assembly turning to how many degrees counterclockwise (CCW)?

To mechanically lock the 7Q1E-10 semitrailer to a tow vehicle, what do we use?

What type of inspection must you perform on the 7Q1E-10 semitrailer before loading?

How many GCU-1/B nylon webbing and tie-down straps can be used to replace a MB-1 tie-down/chain assembly for a double-stacked weapons configuration?

How do you find the location for the chocks on the MHU-141/M munitions handling trailer?

How much power does it take to operate the MHU-141/M munition handling trailer's tail and stop lamps?

When preparing a munitions handling trailer (MHT) for tow, make sure the wheels are in the straight position and the

During extremely cold weather, up to how many minutes can it take the hydraulic pressure to reach the required pressure on the munitions handling trailer (MHT)?

After starting a diesel lift truck, what is the maximum time to wait for the oil pressure gauge to show pressure before stopping the engine and checking for malfunctions?

What do you do when driving loads long distances with the MJ-1 lift truck?

If the electric lift truck motor will not start when you push the start button, you may need to

When preparing the MHU-174/E lift truck for towing, make sure you

On gasoline/diesel lift trucks, the hydraulic fluid level should be

What are the two safety devices on the MHU-186/E hoisting beam?

What do you do with the handling unit legs of the guided missile handling unit when hoisting the air-launched cruise missile (ALCM) onto the MHU-141/M trailer?

When using the MHU-174/E lift truck to handle the missile, make sure the

When preparing to remove the missile from the MHU-141/M munitions handling trailer, do all of the following except

What secures the missile-handling unit to the MHU-141/M munitions handling trailer?

What is required when moving a missile with a lift truck?

What must you do first before lowering the missile and handling unit to the floor with a forklift?

The rear pendulum and fixed attachment fittings are installed in which position on the MHU-196/M munitions handling trailer (MHT) for pylon loader adapter (PLA) mate?

How many shims must you install on each attachment fitting when wrapping the pylon loader adapter (PLA)?

Where do you position the LIFT FORCE POUNDS switch on the munitions handling trailer (MHT) for wrap or launcher operations?

Who establishes access controls to communications security (COMSEC) to properly cleared personnel? Ly cleared personnel?

What is the first step of the operations security (OPSEC) process?

When must your annual communications security (COMSEC) training be complete?

A communications security (COMSEC) deviation is

Which Weapon Storage and Security System (WS3) group provides communications and processing capabilities to status up to 64 vaults?

Which personnel performs as monitoring facility operators (MFO) at the local monitoring facility (LMF)?

The width and wheelbase of the MHU-174/E, MHU-83B/E, and MJ-40/E lift trucks adjust to support different

When can you use forklifts to lift and transport weapons?

What happens when the forklift oil temperature rises above safe operating limits?

On the 6k gasoline engine forklift, how do the lift controls operate?

The three-position, spring-loaded levers on the 6k gasoline engine forklift

What is the minimum amount of tread a forklift's tire can have and still be acceptable?

When starting a forklift, do not hold the starter switch down more than how many seconds?

On a forklift, what determines the travel speed of the forks?

During a pre-use inspection, if you find an MB-1 tie-down device/chain assembly that is cracked what do you do, if anything?

When you install the chain link into the chain recess, what precaution must you observe when using the MB-1 tie-down device/chain assembly?

What is not an authorized method for securing loose MB-1 tie-down/chain assembly ends to prevent damage during shipment?

You use the load binder on the MHU-141/M munitions handling trailers to secure

How do you extend the trap on the CGU-1/B nylon webbing and tie-down strap?

When moving a bomb on a forklift, what factor determines whether forklift spacers are required on the tines?

When you use the H1004 bomb-hoisting adapter to lift a bomb, how do you align the lifting eye?

What is the minimum number, if any, for wheeled pry bars to move warhead containers?

What loading procedure is not authorized on the MHU-141/M munitions handling trailer?

The terms "in" and "out" referenced in the figures and tables of TO 11N-B1004-1, Weapons Loading and Tie-down Procedures, refer to the

When can you load two single-bolstered B83s on the MHU-141/M munitions handling trailer?

During the bomb transfer operation, when do you attach the tie-down devices?

How do you transport the W80 warhead on a MHU-141/M munitions handling trailer?

When payloads are on the MHU-71/E guided missile handling rail sets, for safety you check to make sure

Which munitions handling trailer (MHT) selectable mode affects all four X-Y pads and provides 5 inches of movement during loading or unloading?

What do you do after all the munitions handling trailer (MHT) operations are completed?