FSG#108

A detailed engineering workspace with welding equipment, a technical drawing on a table, and an engineer calculating measurements, bright light illuminating the scene, realistic style.

Welding and Engineering Quiz FSG#108

Test your knowledge in welding, engineering principles, and technical regulations with our comprehensive quiz. Covering various topics from hardness testing to engine dynamics, this quiz is designed for students and enthusiasts alike.

Prepare to challenge yourself with:

Multiple choice questions
Checkbox style queries
Real-world applications

14 Questions4 MinutesCreated by CalculatingEagle47

1.What does 1/8 express for welding?

A. Groove weld size

B. Depth of bevel

C. Root opening

D. Length of weld

2.After technical inspection, the modifications not permitted to the vehicle are:

A. Adjustment of chains and clutches

B. Recharging high voltage batteries

C. Adjustment of tire pressure

D. Adjustment of the position of the aerodynamic device in relation to the vehicle

3.Your team has 5 different drivers. In skidpad driver 1 and 4 have participated. In acceleration Driver 2 and 4. In autocross driver 2 and 3. Which drivers will not have the opportunity to participate in endurance event?

A. Driver 1 and 3

B. Driver 5 and 3

C. Driver 2 and 4

D. Driver 1 and 5

4.For wich of the follwing hardness test correspond the following equation?

A. Knoop microhardness

B. Vickers microhardness

C. Brinell

5.During cost understanding:

A. The team must prove the manufacturing feasibility of the vehicle.

B. Team members may discuss the case of mass production.

C. Team must present the CBOM.

D. Team might present the resource and cost planning.

6.If composite materials are used for any part of the primary structure or the tractive system accumulator container the team must:

A. Build a representative test panel which must measure exactly 270mmx500mm that has the same design, laminate and fabrication method as used for the respective part of the primary structure represented as a flat panel. The sides of the test panel must not be laminated.

B. Build a representative test panel which must measure exactly 275mmx500mm that has the same design, laminate and fabrication method as used for the respective part of the primary structure represented as a flat panel. The sides of the test panel must be laminated.

C. Build a representative test panel which must measure exactly 500mmx275mm that has the same design, laminate and fabrication method as used for the respective part of the primary structure represented as a flat panel. The sides of the test panel must not be laminated.

7.What is the energy output in Joule of a 800uF and 2 Ohm capacitor who is charged with 12Volt source? (Round to nearest thousandths)

A. 0.056

B. 0.057

C. 0.058

D. 0.059

8.Which statement(s) is/are not compatible with the rules?

A. The idle position is the average position of the throttle body while the engine is idling.

B. The throttle must be actuated mechanically by a foot pedal or by an ETC system.

C. The throttle body may be of any size or design.

D. The throttle system mechanism must be protected from debris ingress to prevent jamming.

E. None of the above.

9.Methane, CH4, is burned with dry air. The molar analysis of the products on a dry basis is CO2, 9.7%; CO, 0.5%; O2, 2.95%;and N2, 86.85%. Determine the air–fuel ratio on molar basis,

A. 9.63

B. 9.82

C. 10.36

D. 10.78

10.In EDR, your team has:

A. A cover sheet, a page with the list of contents, 2 pages of text, a page with graphs and tables and 3 pages of drawings (front , top and isometric view)

B. A cover sheet, a page with the list of contents, 3 pages of text and 3 pages of drawings (front, top and side view)

C. A cover sheet, 3 pages of text, and 3 pages of drawings (front , top and side view)

D. A cover sheet, a page with the list of contents, 3 pages of text and 3 pages of drawings (front, top and isometric view)

11.At what temperature titanium’s crystal structure transitions from HCP to FCC?

A. 831°C

B. 812°C

C. 882°C

D. 904°C

12.An oscillator in principle, is one … circuit

A. AC to DC Converter

B. Input Voltage Doubler

C. DC to AC Converter

D. None of the above

13.For wich Reynold number does the transition from laminar to turbulent flow over a flat plate occur?

A. 5*10^3

B. 5*10^4

C. 5*10^5

D. 5*10^6

14.Which of the follwing is correct for deformation by slip?

A. There is no crystallographic reorientation

B. The atomic displacements occur in atomic spacing multiples

C. Occurs in metals having relatively few slip systems

D. Results only small deformations

FSG#108

Welding and Engineering Quiz FSG#108

More Quizzes