Network+ Certification Practice Exam Pt.1
A systems administrator needs to improve WiFi performance in a densely populated office tower and use the latest standard. There is a mix of devices that use 2.4 GHz and 5 GHz. Which of the following should the systems administrator select to meet this requirement?
802.11ac
802.11ax
802.11g
802.11n
Which of the following would be BEST to use to detect a MAC spoofing attack?
Internet Control Message Protocol
Reverse Address Resolution Protocol
Dynamic Host Configuration Protocol
Internet Message Access Protocol
A technician receives feedback that some users are experiencing high amounts of jitter while using the wireless network. While troubleshooting the network, the technician uses the ping command with the IP address of the default gateway and verifies large variations in latency. The technician thinks the issue may be interference from other networks and non-802.11 devices. Which of the following tools should the technician use to troubleshoot the issue?
NetFlow analyzer
Bandwidth analyzer
Protocol analyzer
Spectrum analyzer
Wireless users are reporting intermittent internet connectivity. Connectivity is restored when the users disconnect and reconnect, utilizing the web authentication process each time. The network administrator can see the devices connected to the APs at all times. Which of the following steps will MOST likely determine the cause of the issue?
Verify the session time-out configuration on the captive portal settings
Check for encryption protocol mismatch on the client's wireless settings
Confirm that a valid passphrase is being used during the web authentication
Investigate for a client's disassociation caused by an evil twin AP
A network administrator walks into a datacenter and notices an unknown person is following closely. The administrator stops and directs the person to the security desk. Which of the following attacks did the network administrator prevent?
Evil twin
Tailgating
Piggybacking
Shoulder surfing
A network is experiencing a number of CRC errors during normal network communication. At which of the following layers of the OSI model will the administrator MOST likely start to troubleshoot?
Layer 1
Layer 2
Layer 3
Layer 4
Layer 5
Layer 6
Layer 7
A client recently added 100 users who are using VMs. All users have since reported slow or unresponsive desktops. Reports show minimal network congestion, zero packet loss, and acceptable packet delay. Which of the following metrics will MOST accurately show the underlying performance issues? (Choose two.)
CPU usage
Memory
Temperature
Bandwidth
Latency
Jitter
Client devices cannot enter a network, and the network administrator determines the DHCP scope is exhausted. The administrator wants to avoid creating a new DHCP pool. Which of the following can the administrator perform to resolve the issue?
Install load balancers
Install more switches
Decrease the number of VLANs
Reduce the lease time
An administrator is writing a script to periodically log the IPv6 and MAC addresses of all the devices on a network segment. Which of the following switch features will MOST likely be used to assist with this task?
Spanning Tree Protocol
Neighbor Discovery Protocol
Link Aggregation Control Protocol
Address Resolution Protocol
Which of the following DNS records works as an alias to another record?
AAAA
CNAME
MX
SOA
A company built a new building at its headquarters location. The new building is connected to the company's LAN via fiber-optic cable. Multiple users in the new building are unable to access the company's intranet site via their web browser, but they are able to access internet sites. Which of the following describes how the network administrator can resolve this issue?
Correct the DNS server entries in the DHCP scope
Correct the external firewall gateway address
Correct the NTP server settings on the clients
Correct a TFTP Issue on the company's server
A technician is installing a new fiber connection to a network device in a datacenter. The connection from the device to the switch also traverses a patch panel connection. The chain of connections is in the following order: ✑ Device ✑ LC/LC patch cable ✑ Patch panel ✑ Cross-connect fiber cable ✑ Patch panel ✑ LC/LC patch cable ✑ Switch The connection is not working. The technician has changed both patch cables with known working patch cables. The device had been tested and was working properly before being installed. Which of the following is the MOST likely cause of the issue?
TX/RX is reversed
An incorrect cable was used
The device failed during installation
Attenuation is occurring
A technician is searching for a device that is connected to the network and has the device's physical network address. Which of the following should the technician review on the switch to locate the device's network port?
IP route table
VLAN tag
MAC table
QoS tag
Which of the following provides redundancy on a file server to ensure the server is still connected to a LAN even in the event of a port failure on a switch?
Load balancer
NIC teaming
RAID array
PDUs
An IT organization needs to optimize speeds for global content distribution and wants to reduce latency in high-density user locations. Which of the following technologies BEST meets the organization's requirements?
Load balancing
Geofencing
Public cloud
Content delivery network
Infrastructure as a service
A user reports being unable to access network resources after making some changes in the office. Which of the following should a network technician do FIRST?
Check the system's IP address
Do a ping test against the servers
Reseat the cables into the back of the PC
Ask what changes were made
A new cabling certification is being requested every time a network technician rebuilds one end of a Cat 6 (vendor-certified) cable to create a crossover connection that is used to connect switches. Which of the following would address this issue by allowing the use of the original cable?
CSMA/CD
LACP
PoE+
MDIX
A company hired a technician to find all the devices connected within a network. Which of the following software tools would BEST assist the technician in completing this task?
IP scanner
Terminal emulator
NetFlow analyzer
Port scanner
A technician is installing a high-density wireless network and wants to use an available frequency that supports the maximum number of channels to reduce interference. Which of the following standard 802.11 frequency ranges should the technician look for while reviewing WAP specifications?
2.4GHz
5GHz
6GHz
900MHz
A technician is configuring a network switch to be used in a publicly accessible location. Which of the following should the technician configure on the switch to prevent unintended connections?
DHCP snooping
Geofencing
Port security
Secure SNMP
Which of the following is used to track and document various types of known vulnerabilities?
CVE
Penetration testing
Zero-day
SIEM
Least privilege
The network administrator is informed that a user's email password is frequently hacked by brute-force programs. Which of the following policies should the network administrator implements to BEST mitigate this issue? (Choose two.)
Captive portal
Two-factor authentication
Complex passwords
Geofencing
Role-based access
Explicit deny
A network engineer performs the following tasks to increase server bandwidth: ✑ Connects two network cables from the server to a switch stack ✑ Configure LACP on the switchports Verifies the correct configurations on the switch interfaces Which of the following needs to be configured on the server?
Load balancing
Multipathing
NIC teaming
Clustering
A network technician is manually configuring the network settings for a new device and is told the network block is 192.168.0.0/20. Which of the following subnets should the technician use?
255.255.128.0
255.255.192.0
255.255.240.0
255.255.248.0
Which of the following is the LARGEST MTU for a standard Ethernet frame?
1452
1492
1500
2304
Given the following information, which of the following command-line tools would generate this output?
netstat
arp
dig
tracert
According to troubleshooting methodology, which of the following should the technician do NEXT after determining the most likely probable cause of an issue?
Establish a plan of action to resolve the issue and identify potential effects
Verify full system functionality and, if applicable, implement preventive measures
Implement the solution or escalate as necessary
Test the theory to determine the cause
A technician is installing a cable modem in a SOHO. Which of the following cable types will the technician MOST likely use to connect a modem to the ISP?
Coaxial
Single-mode fiber
Cat 6e
Multimode fiber
Which of the following BEST describes a network appliance that warns of unapproved devices that are accessing the network?
Firewall
AP
Proxy server
IDS
A network technician is reviewing the interface counters on a router interface. The technician is attempting to confirm a cable issue. Given the following information, which of the following metrics confirms there is a cabling issue?
Last cleared
Number of packets output
CRCs
Giants
Multicasts
Which of the following is the physical topology for an Ethernet LAN?
Bus
Ring
Mesh
Star
An IT director is setting up new disaster and HA policies for a company. Limited downtime is critical to operations. To meet corporate requirements, the director set up two different datacenters across the country that will stay current on data and applications. In the event of an outage, the company can immediately switch from one datacenter to another. Which of the following does this BEST describe?
A warm site
Data mirroring
Multipathing
Load balancing
A hot site
The management team needs to ensure unnecessary modifications to the corporate network are not permitted and version control is maintained. Which of the following documents would BEST support this?
An incident response plan
A business continuity plan
A change management policy
An acceptable use policy
Which of the following is MOST likely to generate significant East-West traffic in a datacenter?
A backup of a large video presentation to cloud storage for archival purposes
A duplication of a hosted virtual server to another physical server for redundancy
A download of navigation data to a portable device for offline access
A query from an IoT device to a cloud-hosted server for a firmware update
A technician is troubleshooting a network switch that seems to stop responding to requests intermittently whenever the logging level is set for debugging. Which of the following metrics should the technician check to begin troubleshooting the issue?
Audit logs
CPU utilization
CRC errors
Jitter
A technician wants to deploy a new wireless network that comprises 30 WAPs installed throughout a three-story office building. All the APs will broadcast the same SSID for client access. Which of the following BEST describes this deployment?
Extended service set
Basic service set
Unified service set
Independent basic service set
A user tries to ping 192.168.1.100 from the command prompt on the 192.168.2.101 network but gets the following response: U.U.U.U. Which of the following needs to be configured for these networks to reach each other?
Network address translation
Default gateway
Loopback
Routing protocol
A branch of a company recently switched to a new ISP. The network engineer was given a new IP range to assign. The ISP assigned 196.26.4.0/26, and the branch gateway router now has the following configurations on the interface that peers to the ISP. The network engineer observes that all users have lost Internet connectivity. Which of the following describes the issue?
The incorrect subnet mask was configured
The incorrect gateway was configured
The incorrect IP address was configured
The incorrect interface was configured
Within the realm of network security, Zero Trust:
prevents attackers from moving laterally through a system.
allows a server to communicate with outside networks without a firewall.
block malicious software that is too new to be found in virus definitions.
stops infected files from being downloaded via websites.
Which of the following service models would MOST likely be used to replace on-premises servers with a cloud solution?
PaaS
IaaS
SaaS
Disaster recovery as a Service (DRaaS)
Which of the following factors should be considered when evaluating a firewall to protect a datacenter's east-west traffic?
Replication traffic between an on-premises server and a remote backup facility
Traffic between VMs running on different hosts
Concurrent connections generated by Internet DDoS attacks
VPN traffic from remote offices to the datacenter's VMs
Which of the following is used to prioritize Internet usage per application and per user on the network?
Bandwidth management
Load balance routing
Border Gateway Protocol
Administrative distance
A network administrator needs to query the NSs for a remote application. Which of the following commands would BEST help the administrator accomplish this task?
arp
hostname
dig
show interface
Which of the following would MOST likely be used to review previous upgrades to a system?
Business continuity plan
Change management
System life cycle
Standard operating procedures
A technician is deploying a new switch model and would like to add it to the existing network monitoring software. The technician wants to know what metrics can be gathered from a given switch. Which of the following should the technician utilize for the switch?
MIB
Trap
Syslog
Audit log
A network device is configured to send critical events to a syslog server; however, the following alerts are not being received: Severity 5 LINK-UPDOWN: Interface 1/1, changed state to down Severity 5 LINK-UPDOWN: Interface 1/3, changed state to down Which of the following describes the reason why the events are not being received?
The network device is not configured to log that level to the syslog server
The network device was down and could not send the event
The syslog server is not compatible with the network device
The syslog server did not have the correct MIB loaded to receive the message
A network administrator is implementing OSPF on all of a company's network devices. Which of the following will MOST likely replace all the company's hubs?
A Layer 3 switch
A proxy server
A NGFW
A WLAN controller
A network administrator discovers that users in an adjacent building are connecting to the company's guest wireless network to download inappropriate material. Which of the following can the administrator do to MOST easily mitigate this issue?
Adjust the wireless channels
Reduce the wireless power levels
Enable wireless client isolation
Enable wireless port security
A network administrator is designing a new datacenter in a different region that will need to communicate to the old datacenter with a secure connection. Which of the following access methods would provide the BEST security for this new datacenter?
Virtual network computing
Secure Socket Shell
In-band connection
Site-to-site VPN
Which of the following is MOST commonly used to address CVEs on network equipment and/or operating systems?
Vulnerability assessment
Factory reset
Firmware update
Screened subnet
An attacker is attempting to find the password to a network by inputting common words and phrases in plaintext to the password prompt. Which of the following attack types BEST describes this action?
Pass-the-hash attack
Rainbow table attack
Brute-force attack
Dictionary attack
Which of the following technologies provides a failover mechanism for the default gateway?
FHRP
LACP
OSPF
STP
The following configuration is applied to a DHCP server connected to a VPN concentrator. There are 300 non-concurrent sales representatives who log in for one hour a day to upload reports, and 252 of these representatives are able to connect to the VPN without any Issues. The remaining sales representatives cannot connect to the VPN over the course of the day. Which of the following can be done to resolve the issue without utilizing additional resources?
Decrease the lease duration
Reboot the DHCP server
Install a new VPN concentrator
Configure a new router
A technician needs to configure a Linux computer for network monitoring. The technician has the following information. After connecting the Linux computer to the mirror port on the switch, which of the following commands should the technician run on the Linux computer?
ifconfig eth1 hw ether A1:B2:C3:D4:E5:F6
ifconfig eth0 10.1.2.3
ifconfig eth0 promisc
ifconfig eth1 up
A network engineer is investigating reports of poor network performance. Upon reviewing a device configuration, the engineer finds that duplex settings are mismatched on both ends. Which of the following would be the MOST likely result of this finding?
Increased device temperature
Increased CRC errors
Increased giants and runts
Increased switching loops
Which of the following devices would be used to manage a corporate WLAN?
A wireless NAS
A wireless bridge
A wireless router
A wireless controller
Which of the following types of devices can provide content filtering and threat protection, and manage multiple IPSec site-to-site connections?
Layer 3 switch
VPN headend
Next-generation firewall
Proxy server
Intrusion prevention
An engineer notices some late collisions on a half-duplex link. The engineer verifies that the devices on both ends of the connection are configured for half duplex. Which of the following is the MOST likely cause of this issue?
The link is improperly terminated
One of the devices is misconfigured
The cable length is excessive
One of the devices has a hardware issue
A network administrator is configuring a load balancer for two systems. Which of the following must the administrator configure to ensure connectivity during a failover?
VIP
NAT
APIPA
IPv6 tunneling
Broadcast IP
A technician is troubleshooting a wireless connectivity issue in a small office located in a high-rise building. Several APs are mounted in this office. The users report that the network connections frequently disconnect and reconnect throughout the day. Which of the following is the MOST likely cause of this issue?
The AP association time is set too low
EIRP needs to be boosted
Channel overlap is occurring
The RSSI is misreported
A network engineer configured new firewalls with the correct configuration to be deployed to each remote branch. Unneeded services were disabled, and all firewall rules were applied successfully. Which of the following should the network engineer perform NEXT to ensure all the firewalls are hardened successfully?
Ensure an implicit permit rule is enabled
Configure the log settings on the firewalls to the central syslog server
Update the firewalls with current firmware and software
Use the same complex passwords on all firewalls
At which of the following OSI model layers would a technician find an IP header?
Layer 1
Layer 2
Layer 3
Layer 4
An engineer is configuring redundant network links between switches. Which of the following should the engineer enable to prevent network stability issues?
802.1Q
STP
Flow control
CSMA/CD
Several WIFI users are reporting the inability to connect to the network. WLAN users on the guest network are able to access all network resources without any performance issues. The following table summarizes the findings after a site survey of the area in question. Which of the following should a wireless technician do NEXT to troubleshoot this issue?
Reconfigure the channels to reduce overlap
Replace the omni antennas with directional antennas
Update the SSIDs on all the APs
Decrease power in AP 3 and AP 4
Which of the following routing protocols is used to exchange route information between public autonomous systems?
OSPF
BGP
EIGRP
RIP
A fiber link connecting two campus networks is broken. Which of the following tools should an engineer use to detect the exact break point of the fiber link?
OTDR
Tone generator
Fusion splicer
Cable tester
PoE injector
Which of the following can be used to centrally manage credentials for various types of administrative privileges on configured network devices?
SSO
TACACS+
Zero Trust
Separation of duties
Multifactor authentication
A network technician is installing new software on a Windows-based server in a different geographical location. Which of the following would be BEST for the technician to use to perform this task?
RDP
SSH
FTP
DNS
Branch users are experiencing issues with videoconferencing. Which of the following will the company MOST likely configure to improve performance for these applications?
Link Aggregation Control Protocol
Dynamic routing
Quality of service
Network load balancer
Static IP addresses
A technician is assisting a user who cannot connect to a network resource. The technician first checks for a link light. According to troubleshooting methodology, this is an example of:
using a bottom-to-top approach
establishing a plan of action
documenting a finding
questioning the obvious
Which of the following transceiver types can support up to 40Gbps?
SFP+
QSFP+
SFP
QSFP
Which of the following TCP ports is used by the Windows OS for file sharing?
53
389
445
1433
A network administrator redesigned the positioning of the APs to create adjacent areas of wireless coverage. After project validation, some users still report poor connectivity when their devices maintain an association to a distanced AP. Which of the following should the network administrator check FIRST?
Validate the roaming settings on the APs and WLAN clients
Verify that the AP antenna type is correct for the new layou
Check to see if MU-MIMO was properly activated on the APs
Deactivate the 2.4GHz band on the APS
Which of the following connector types would have the MOST flexibility?
SFP
BNC
LC
RJ45
Which of the following ports is commonly used by VoIP phones?
20
143
445
5060
A network engineer is investigating reports of poor network performance. Upon reviewing a report, the engineer finds that jitter at the office is greater than 10ms on the only WAN connection available. Which of the following would be MOST affected by this statistic?
An in-office video call with a coworker
Routing table from the ISP
A VoIP sales call with a customer
Firewall CPU processing time
A network technician needs to ensure outside users are unable to telnet into any of the servers at the datacenter. Which of the following ports should be blocked when checking firewall configuration?
22
23
60
3389
8080
A technician is writing documentation regarding a company's server farm. The technician needs to confirm the server name for all Linux servers. Which of the following commands should the technician run?
ipconfig
nslookup
arp
route
A technician is connecting multiple switches to create a large network for a new office. The switches are unmanaged Layer 2 switches with multiple connections between each pair. The network is experiencing an extreme amount of latency. Which of the following is MOST likely occurring?
Ethernet collisions
A DDoS attack
A broadcast storm
Routing loops
A store owner would like to have secure wireless access available for both business equipment and patron use. Which of the following features should be configured to allow different wireless access through the same equipment?
MIMO
TKIP
LTE
SSID
Which of the following systems would MOST likely be found in a screened subnet?
RADIUS
FTP
SQL
LDAP
Which of the following would need to be configured to ensure a device with a specific MAC address is always assigned the same IP address from DHCP?
Scope options
Reservation
Dynamic assignment
Exclusion
Static assignment
Access to a datacenter should be individually recorded by a card reader even when multiple employees enter the facility at the same time. Which of the following allows the enforcement of this policy?
Motion detection
Access control vestibules
Smart lockers
Cameras
A workstation is configured with the following network details. Software on the workstation needs to send a query to the local subnet broadcast address. To which of the following addresses should the software be configured to send the query?
10.1.2.0
10.1.2.1
10.1.2.23
10.1.2.255
10.1.2.31
After the A record of a public website was updated, some visitors were unable to access the website. Which of the following should be adjusted to address the issue?
TTL
MX
TXT
SOA
A network administrator is installing a wireless network at a client's office. Which of the following IEEE 802.11 standards would be BEST to use for multiple simultaneous client access?
CDMA
CSMA/CD
CSMA/CA
GSM
A technician is installing multiple UPS units in a major retail store. The technician is required to keep track of all changes to new and old equipment. Which of the following will allow the technician to record these changes?
Asset tags
A smart locker
An access control vestibule
A camera
Which of the following attacks encrypts user data and requires a proper backup implementation to recover?
DDoS
Phishing
Ransomware
MAC spoofing
A network administrator wants to analyze attacks directed toward the company's network. Which of the following must the network administrator implement to assist in this goal?
A honeypot
Network segmentation
Antivirus
A screened subnet
A network administrator is configuring a database server and would like to ensure the database engine is listening on a certain port. Which of the following commands should the administrator use to accomplish this goal?
nslookup
netstat -a
ipconfig /a
arp -a
A technician is implementing a new wireless network to serve guests at a local office. The network needs to provide Internet access but disallow associated stations from communicating with each other. Which of the following would BEST accomplish this requirement?
Wireless client isolation
Port security
Device geofencing
DHCP snooping
A company requires a disaster recovery site to have equipment ready to go in the event of a disaster at its main datacenter. The company does not have the budget to mirror all the live data to the disaster recovery site. Which of the following concepts should the company select?
Cold site
Hot site
Warm site
Cloud site
An IT technician suspects a break in one of the uplinks that provides connectivity to the core switch. Which of the following command-line tools should the technician use to determine where the incident is occurring?
nslookup
show config
netstat
show interface
show counters
A technician is connecting DSL for a new customer. After installing and connecting the on-premises equipment, the technician verifies DSL synchronization. When connecting to a workstation, however, the link LEDs on the workstation and modem do not light up. Which of the following should the technician perform during troubleshooting?
Identify the switching loops between the modem and the workstation.
Check for asymmetrical routing on the modem.
Look for a rogue DHCP server on the network.
Replace the cable connecting the modem and the workstation.
Which of the following services can provide data storage, hardware options, and scalability to a third-party company that cannot afford new devices?
SaaS
IaaS
PaaS
DaaS
A network administrator is talking to different vendors about acquiring technology to support a new project for a large company. Which of the following documents will MOST likely need to be signed before information about the project is shared?
BYOD policy
NDA
SLA
MOU
Two remote offices need to be connected securely over an untrustworthy MAN. Each office needs to access network shares at the other site. Which of the following will BEST provide this functionality?
Client-to-site VPN
Third-party VPN service
Site-to-site VPN
Split-tunnel VPN
A network requirement calls for segmenting departments into different networks. The campus network is set up with users of each department in multiple buildings. Which of the following should be configured to keep the design simple and efficient?
MDIX
Jumbo frames
Port tagging
Flow control
Which of the following protocols will a security appliance that is correlating network events from multiple devices MOST likely rely on to receive event messages?
Syslog
Session Initiation Protocol
Secure File Transfer Protocol
Server Message Block
Which of the following is MOST commonly used to address CVEs on network equipment and/or operating systems?
Vulnerability assessment
Factory reset
Firmware update
Screened subnet
A network technician is investigating an issue with handheld devices in a warehouse. Devices have not been connecting to the nearest APs, but they have been connecting to an AP on the far side of the warehouse. Which of the following is the MOST likely cause of this issue?
The nearest APs are configured for 802.11g.
An incorrect channel assignment is on the nearest APs.
The power level is too high for the AP on the far side.
Interference exists around the AP on the far side.
Which of the following OSI model layers is where conversations between applications are established, coordinated, and terminated?
Session
Physical
Presentation
Data link
Which of the following uses the destination IP address to forward packets?
A bridge
A Layer 2 switch
A router
A repeater
A business is using the local cable company to provide Internet access. Which of the following types of cabling will the cable company MOST likely use from the demarcation point back to the central office?
Multimode
Cat 5e
RG-6
Cat 6
100BASE-T
A network administrator decided to use SLAAC in an extensive IPv6 deployment to alleviate IP address management. The devices were properly connected into the LAN but autoconfiguration of the IP address did not occur as expected. Which of the following should the network administrator verify?
The network gateway is configured to send router advertisements.
A DHCP server is present on the same broadcast domain as the clients.
The devices support dual stack on the network layer.
The local gateway supports anycast routing.
{"name":"Network+ Certification Practice Exam Pt.1", "url":"https://www.quiz-maker.com/QTNLJUQ5F","txt":"A systems administrator needs to improve WiFi performance in a densely populated office tower and use the latest standard. There is a mix of devices that use 2.4 GHz and 5 GHz. Which of the following should the systems administrator select to meet this requirement?, Which of the following would be BEST to use to detect a MAC spoofing attack?, A technician receives feedback that some users are experiencing high amounts of jitter while using the wireless network. While troubleshooting the network, the technician uses the ping command with the IP address of the default gateway and verifies large variations in latency. The technician thinks the issue may be interference from other networks and non-802.11 devices. Which of the following tools should the technician use to troubleshoot the issue?","img":"https://www.quiz-maker.com/3012/CDN/97-4781628/screen-shot-2024-01-17-at-7-50-25-pm.png?sz=1200-00000000001000001328"}
Make your own Survey
- it's free to start.
- it's free to start.