Engineering Compliance and Technical Knowledge Quiz
Engineering Compliance and Technical Knowledge Quiz
Test your understanding of engineering compliance and technical principles with our comprehensive quiz. Designed for students and professionals alike, this quiz will challenge your knowledge on various topics, including technical specifications, safety regulations, and engineering fundamentals.
Key features:
- Multiple choice questions
- Focus on practical applications and rules
- Instant feedback on your answers
1.Which statement is in compliance with the rules?
Where more than one exhaust outlet is present, the test will be repeated for each exhaust and the average reading will be used.
A completed DSS must be submitted on the event's start.
Burnouts prior to and during the events are prohibited.
4.5 points are awarded to every team that finishes at least one run without DNF or DQ in skidpad.
2.A team missed the initial deadline for SESA document and submitted this 49 hours after the deadline. After that the team got an official request to make a correction of this document and missed the given deadline of 168 hours and upload the revised version 172 hours too late. What total penalty will the team receive for the submission of this document?
30 points
De-registration
65 points
100 points
3.Which statement is in compliance with the rules?
Vehicles may not be presented for design judging without having passed technical inspection.
All suspension mounting points must be visible at technical inspection only by direct view.
All onsite participants can sign a liability waiver upon registering on site which can be found on the competition website.
None.
4.The following capacitor has relative permitivity ε=2.1, Plate area S=0.5cm^2 and distance between plates d=1.2mm. What is the capacitance of the capacitor in uF?
7.847
7.474
7.747
7.774
5.The upper support member of the front bulkhead:
Must be attached to the front bulkhead a maximum of 50 mm above the top-most surface of the front bulkhead.
Must be attached to the front bulkhead a maximum of 50 mm below the top-most surface of the front hoop.
Must be attached to the front bulkhead no more than 50 mm above the top-most surface of the front bulkhead.
Must be attached to the front bulkhead no more than 50 mm below the upper surface of the front bulkhead.
6.In a parallel RLC circuit, which value may always be used as a vector reference?
Current
Reactance
Resistance
Voltage
8.Which of the following is/are not true about BPP?
The team members who have been introduced must answer the judges’ questions even if they were not actually presenting.
Any presentation exceeding ten minutes will carry on with a penalty of 5 points for any additional minute.
Three members must present the BPP.
Your team made it to the BPP finals and scored 70.9 points.
9.At a very low temperature, a semiconductor:
Becomes a conductor
Becomes an insulator
May become a conductor or an insulator
Will remain a semiconductor
10.Your team missed the following items from the BOM: Front Uprights and a layer of Pre-Preg on a part. What’s the total penalty?
8
5
6
4
11.When the driver sees a red and yellow striped flag,he/she must:
Exit the track at the first opportunity
Pull into the driver change area for a mechanical inspection of the vehicle
Come to an immediate safe and controlled stop on the track and must follow track marshals directions
Be prepared for evasive maneuvers to avoid a difficult situation on the track
12.A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters respectively equal to 40 and 60 mm. What is the largest torque that can be applied to the shaft if the shearing stressis not to exceed 120 MPa?
3.68 kN*m
4.08 kN*m
4.23 kN*m
6.32 kN*m
{"name":"Engineering Compliance and Technical Knowledge Quiz", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your understanding of engineering compliance and technical principles with our comprehensive quiz. Designed for students and professionals alike, this quiz will challenge your knowledge on various topics, including technical specifications, safety regulations, and engineering fundamentals. Key features: Multiple choice questions Focus on practical applications and rules Instant feedback on your answers","img":"https:/images/course6.png"}
More Surveys
Policy Organization
7431
Transformer Basics Survey
10515
PSSR question summary
7430
Safety Analyst Training
17835
SMIT
10546
IATSE 320 Training Survey
7426
Bu 2 transportation systems (parts of escalator not included)
52260
Flight Control System
1266
Clinical Capstone Case Study Project Quiz
5220
Bromatology Pro.Chanra (2)&Pro.Mary(1)
753827
Pre-diabetes Case Study Post-Test
5223