FB 2020
Vehicle Safety and Design Quiz
Test your knowledge on vehicle safety standards and design specifications with our comprehensive quiz. This quiz consists of 31 questions that cover various aspects of automotive engineering, from safety devices to structural requirements.
Prepare yourself for:
- Detailed questions on vehicle construction
- Insights into safety protocols
- Challenging multiple-choice format
BSPD stands for
Brake system Plausibility Device
Brake System Prevention Device
Binary System Plausibity Device
Binary System Prevention Device
Part of vehicle which provides protection of driver's feet.
Front Hoop
Front Bulkhead
Front Hoop Bracing
Front Bulkhead Support
A removable device that attaches to the rear of the vehicle and allows two people to push and pull the vehicle while standing erect behind the vehicle.
Pushbar
Quickjack
AIP
ABS
This assembly may be single welded structure, double welded structure or a combination of composite and welded structure.The fabricated structure assembly that supports all functional vehicle systems together.
Swing Arm
Chasis
Chasis Member
Front Hoop Bracing
Deformable energy absorbing device located at forward of the front Bulkhead
Front Bulkhead Support
Front Bulkhead Support System
Rollover Protection Envelope
Impact Attenuator
A roll bar located alongside or just behind the driver's torso
Main hoop
Behind hoop
Roll hoop
None
All edges of the bodywork that could come into contact with a pedestrian must have a minimum radius of
1mm
1.5mm
0.85mm
2.5mm
The bodywork in front of the front wheels must have a radius of "R" mm and extend atleast an angle of " ____° " relative to the forward direction along the top sides and bottom of all affected edges.
18mm, 45°
30mm, 50°
38mm, 40°
38mm, 45°
Minimum static ground clearance of any portion of the vehicle, other than tires, including a driver, must be
32mm
31mm
30mm
29mm
The Minimum Groove Depth should be
1.4mm
2.4mm
2.2mm
2.0mm
The steering wheel must be no more than ______ rearward of the front hoop.
220mm
230mm
250mm
240mm
The vehicle must have a wheelbase of
1515mm
1425mm
1525mm
1625mm
Steel Tubing has to be made from unalloyed carbon steel with a maximum content of
0.3% Carbon, 1.7% Manganese and 0.6% other element
0.3% Carbon, 1.2% Manganese and 0.6% other element
0.2% Carbon, 1.7% Manganese and 0.6% other element
0.2% Carbon, 1.2% Manganese and 0.6% other element
Minimum Tubing Wall Thickness should not be less than
1mm
2mm
1.1mm
1.2mm
The minimum radius of any bend,measured at tube centerline, must be atleast
2 TIMES
3 TIMES
4 TIMES
None
The main hoop has to be constructed from
Single piece
Double piece
Multiple piece
None
If the front hoop is made from multiple pieces, it has to be separated using
Node-node triangulation
Equivalent construction
Both a&b
None
In side view, no part of front hoop can be inclined more than ____ from vertical
10°
20°
30°
40°
Formula Bharat Is Hosted by
Bharat Pvt. Ltd
Curiosum Tech Pvt. Ltd.
Digital Bharat Pvt.Ltd
Phoenix Pvt. Ltd.
AIP stands for
Active injection Pedal
Accumulator isolation Plate
Anti Intrusion Plate
Accumulator Injection Pedal
Two lines extending vertically from positions 75 mm in front of and 75 mm behind the outer diameter of the front and rear tires in the side view of the vehicle, with steering straight ahead.
Monocoque
Keep out zone
Both a&b
None
Steel tubing should not have area moment of inertia less than
5595mm^4
6695mm^4
4995mm^4
3395mm^4
Roll hoops must have one ______ hole in a non-critical straight location and its surface at this point must be unobstructed for at least _______°.
4.5 mm , 180
3.5mm, 165
4.5 mm , 180
3.5mm, 165
The main hoop braces must be attached to the main hoop no lower than _____ mm below the top-most surface of the main hoop. The included angle formed by the main hoop and the main hoop braces must be at least _____°
160mm, 30
150mm,45
150mm, 15
130mm,60
Which of these is not a non-crushable object?
Pedals
Master cylinder
Hydraulic Reservoir
Driver's Cabin
Position with a seat back angled at 30° or less from the vertical as measured along the line joining the two 200 mm circles of the 95th percentile male template
Reclined Driving Position
Upright Driving Position
Downward Driving Position
Inclined Driving Position
This switch must be installed so that in the event of a failure in at least one of the brake circuits the brake pedal over travel will result in the shutdown circuit being opened. This must function for all possible brake pedal and brake balance settings without damaging any part of the vehicle. Identify the switch.
BAT Switch
BIT Switch
BFT Switch
BOT Switch
All forward facing edges of aerodynamic devices that could contact a pedestrian must have a minimum radius of ____ mm for all horizontal edges and ____ mm for vertical edges.
5mm, 3mm
5mm,2mm
4mm, 3mm
4mm,2mm
Methods accepted as positive locking mechanisms
Locking plates
Prevailing torque lock nuts
Both a&b
None of these
The engine(s) used to power the vehicle must be piston engine(s) using a four-stroke primary heat cycle with a displacement not exceeding _____ cm3 per cycle.
710
715
725
720
{"name":"FB 2020", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your knowledge on vehicle safety standards and design specifications with our comprehensive quiz. This quiz consists of 31 questions that cover various aspects of automotive engineering, from safety devices to structural requirements.Prepare yourself for:Detailed questions on vehicle constructionInsights into safety protocolsChallenging multiple-choice format","img":"https:/images/course4.png"}
More Quizzes
QUIZZELLA 2
1589
Automotive Safety Standards Quiz
15821
Rulebook test ENGINE dept
10512
Quiz1
10525
Engineering Inspection Challenge
840
Formula bharat rule book practice quiz
1588
FSG#309
13613
Automotive Knowledge Quiz
1166
Formula bharat
1587
Probequiz Ecurie Aix
1260
Safety and Compliance Quiz
15815
Formula bharat
1588
Make your own Survey
- it's free to start.
- it's free to start.