Formula Student Quiz Challenge
Formula Student Quiz Challenge
Test your knowledge on various aspects of Formula Student vehicles and engineering in our engaging quiz! Whether you're a student, engineer, or just enthusiastic about motorsports, this quiz is designed for you.
- 15 thought-provoking questions
- Multiple choice format
- Learn and validate your understanding
A Formula Student vehicle with a constant power of 25 kW accelerates from standstill over 75m in 5.0 s with Driver A. With Driver B the same acceleration takes 5.1 s. Given that the acceleration resistance is the only resistance to overcome (no friction loss, no additional inertia, flat surface, no aerodynamic resistance, infinite grip): how much heavier is Driver B? Answer in kilogramms and round to 1 decimal place.
8.5
17.0
30.2
0.0
0.3
26.9
Calculate the force FBx for the given bracket when a force F=880 N is applied at the point of the thick red arrow, given the dimensions l1=45mm and l2=55mm. Answer in Newton and round to 0 decimal places.
720
-720
1076
-880
-1076
880
Cos(x)sin(x) =
Tan(x)
0.5*sin(2x)
Cot(x)
0.5
X
When will the FSG 2019 Quiz take place?
01.02.2018 13:00 CET
01.02.2019 11:00 CET
01.02.2019 15:00 ET
01.02.2019 12:00 EET
01.02.2019 14:00 EET
During charging you monitor the cell temperatures by tapping the BMS CAN Bus. The Temperature is transmitted as 16-bit unsigned integer (0.00229 °C/bit). Looking at the data the temperatures look somewhat implausible (see picture below) - what went wrong most likely?
The can bus is overloaded
The conversion factor is wrong
The signed-ness is wrong
This is actually the cell voltage
The endianess is wrong
Your self-developed electronic control module needs 200ms to safely shut down and write back data into nonvolatile memory. How big would the power regulator output capacitance need to be at least to do that in the event of a unexpected shutdown (GLV Master switch turn-off), given that:; The device needs a constant current of 120mA; The regulated voltage is 5V; The CPU will brown-out at 3.8V; There is no reverse-flow back into the supply
220 μF
17.5 mF
20.000 μF
1.2 F
47 μF
2000 μF
With which categories you can reach the maximum points?
Localisation & Mapping, Safety & Security, Data Visialisation / Usage of Tools, Planning
Sensor Data Interpretation, Vehicle Networking / Data Processing, Validation, Simulation & Testing, Hardware Development
Hardware Development, Software Development, Sensor Data Interpretation, Autonomous Design Report
Planning, Vehicle Networking / Data Processing, Localisation & Mapping, Autonomous Design Report
You want to analyze the following recurrence relation using the master theorem. What is the result given in Big O notation? Recurrence relation:
A)
B)
C)
D)
Consider this discharge Circuit. What does the input do?
Input HIGH enables the discharge
Input LOW enables the discharge
The input does nothing
Input HIGH shorts the HV
If any type tube diameter and wall thickness would be available how much would 1 m of shoulder harness steel tube weight if we choose the lightest? (Density is 7.85 g/cm^3)
1.378 kg
1.0 kg
1.198 kg
1.511 kg
1.225 kg
Which of the following sensors makes use of the Seebeck Effect?
Thermistor
Thermocouple
Contactless position sensor
Wideband Oxygen Sensor
Who must attend the team briefing every morning?
Only the faculty advisor.
All team members.
The faculty advisor and all drivers.
The team captain and the drivers who want to drive at the respective day
Which reason for disqualification in the Endurance event is especially mentioned in the rules?
A malfunctioning brake light
Tires with a very low grip level
An ugly driver
Low oil pressure in left corners
Kicking more than 5 cones in a row
What has not to be entered to the user profile for participating at FSG?
Personal address
Clothing size
Personal height
Emergency contact person and phone (e.g. parents)
Valid Health Insurance Certificate (HIC) for Germany (e.g. Travel insurance)
Current target degree of study
Which of the followings should NOT be in the Engineering Design Report?
Three-view drawings
Detailed specifications of the vehicle
Brief textural description of the design, manufacturing and testing process
Pictures, graphs illustrating the design, manufacturing and testing process
{"name":"Formula Student Quiz Challenge", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your knowledge on various aspects of Formula Student vehicles and engineering in our engaging quiz! Whether you're a student, engineer, or just enthusiastic about motorsports, this quiz is designed for you.15 thought-provoking questionsMultiple choice formatLearn and validate your understanding","img":"https:/images/course5.png"}
More Surveys
Data Intelligence Team Weekly Fair
9413
Let's know more about you
4269
Transformer Basics Survey
10515
Safety Analyst Training
17836
KENJO REMOTE WORK SURVIVOR
15813
Discord mod for Based Crusaders server
14714
The Scrum Framework
1478
Agile Maturity Test
1050
Chart visualization 101
12623
KhanLife Official Staff Applications
10517
Admin Applications
9415
Excel Training
5231
Make your own Survey
- it's free to start.
- it's free to start.