FS Spain 2020 Registration Quiz

A high-tech racing car in a dynamic setting, symbolizing engineering and competition with elements of motorsport safety and regulations, vibrant colors, and a futuristic design.

FS Spain 2020 Registration Quiz

Test your knowledge on the technical and regulatory aspects of the FS Spain 2020 competition with our comprehensive quiz. This quiz is designed for participants, engineers, and enthusiasts alike to sharpen their understanding and retention of important guidelines and practices.

Key topics include:

Driver Equipment Regulations
Vehicle Technical Specifications
Safety Standards and Compliance
Electrical Systems and Circuitry

12 Questions3 MinutesCreated by TestingWizard157

Choose all true sentences from the ones below.

Any TS shielded cable must have the shield grounded.

If the driver during braking locks the wheels while more than 5kW are delivered to the motors for a period longer than 500ms, then the BSPD will open the SDC.

The capacity of a battery is measured in milliamperes.

For all attachments of the Accumulator Container, T10 applies.

Which sentence is not true about the driver's equipment?

A driver must wear fire resistant socks when the car is pushed from the garage to the skidpad area.

Arm restraints must be commercially manufactured.

During the technical inspection, a helmet may be impounded due to wear.

Removal of driver equipment during a dynamic event may lead to a disqualification.

A car and a truck are both travelling with a constant speed of 20 m/s on a narrow road. The car is 10m behind the truck. The truck driver suddenly applies his brakes, causing the truck to decelerate at a constant rate of 2m/s^2. Two seconds later the driver of the car applies his brakes and marginally manages to avoid a rear-end collision. Determine the constant deceleration of the car in m/s^2. Round your answer to the first decimal.

2 m/s^2

3.3 m/s^2

6.6 m/s^2

4 m/s^2

Which of the following are true?

The hum of a CRT TV is caused by the transformer controlling the horizontal movement of the electron beam.

A zener diode is used in voltage regulating circuits because of its forward voltage.

Starting a very large synchronous motor is difficult because of its inertia. In this case, a squirrel cage winding can be used if the motor is not electronically controlled.

Induction heating utilizes the the heated material’s electrical resistance.

For the depicted circuit, calculate the equivalent capacitance, if all capacitors are the same, with C = 25nF. Give answer in pF, rounded to the second decimal.

Assume that the following circuit has reached a steady state. What is the voltage across the capacitor? The current source produces 2A. Round to the first decimal.

Choose the true statements.

IF the BOTS or the Inertia Switch open the SDC, power cycling of the LVMS will reset their state.

A single brake acting on a limited-slip differential is permitted.

Vehicle numbers must appear on the vehicle at the front and both sides and be at least 150mm high.

A TS component rated for 85 degrees Celsius is sufficient.

Choose the wrong sentences.

A harness attachment to a monocoque using three 6mm metric grade 8.8 bolts (or bolts of an equivalent norm) and steel backing plates with a thickness of 2 mm is allowed

Changing the position of a winglet on the rear wing without changing its angle of attack is permitted by the FS Rules.

A sheet of DuPont’s Nomex 410 with a thickness of 0.13mm is appropriate to separate HV and LV components in the same enclosure.

To measure tire pressure, a pressure sensor can be installed inside the tire.

Team e-Prom submitted the SES on March 25th 16:00. 24 hours later they received a notification about improving a not fully defined part. They submitted the corrected version on April 3rd 17:59. In addition, e-Prom submitted the BPPV document on May 6th 10:00. As for the VSV, they submitted it at the start of the third day after the deadline and received a pass upon evaluation. How many penalty points did e-Prom get? Deadlines: Group A: March 23th 12:00, 2020 Group B: April 29th 12:00, 2020 Group C: May 7th 12:00, 2020 Group D: May 15th 12:00, 2020

Which of the following are false?

A FBH tube with a area moment of inertia of 8409mm^4 is rules compliant.

A material with properties equivalent to that of 3 baseline tubes is appropriate for use in the horizontal part of the FBHS.

No heat-treatment information is needed for the SES in case that the welded parts are made from exactly the same material.

In side view, no part of the front hoop may be inclined more than 10 degrees from vertical.

A Shoulder Harness should never deviate more than 10 degrees from horizontal in side view.

FS Spain 2020 Registration Quiz

FS Spain 2020 Registration Quiz

More Surveys