COCKPIT GUIDELINE

Which of the following is TRUE regarding the Canopy Lock Handle ?

Acts as a physical barrier to canopy switch when lock

Cuts off electrical power to external canopy switch

Prevent accidental advancement of the throttle to the after burner position during parking

All of the above

Before entering the cockpit, you must ensure there are _____ safety pins installed in the Egress System for the F16C, F16D/D+, F16C(MLU) and F16D/D+(MLU) respectively.

F16C (2 pins), F16D/D+ (4 pins), F16C (2 pins) F16D/D+ (4 pins)

F16C (3 pins), F16D/D+ (6 pins), F16C (4 pins) F16D/D+ (8 pins)

F16C (4 pins), F16D/D+ (8 pins), F16C (3 pins) F16D/D+ (6 pins)

F16C (4 pins), F16D/D+ (8 pins), F16C (4 pins) F16D/D+ (8 pins)

Care must be exercise to ensure that the canopy actuator (F16C) is not in continuous operation for _____ .

1 minute without 3 minutes cool down period

1 minute without 5 minutes cool down period

3 minute without 1 minutes cool down period

5 minute without 1 minutes cool down period

The correct position of the crew entry ladder is important, it will not damage the __________ .

DTA lines

Switches on the throttle

Transparency on the canopy

Switches on the side stick control

What must you ensure if the canopy is required to open and close manually?

Canopy lock handle in the lock position

Tools or FOD are left on the longeron

Crew entry ladder is placed correctly at the appropriate position

Rotate manual drive in the correct direction

Which T.O contains the maintenance instructions for F-16 Aircraft Cockpit Safety?

SN1F-16CJ-2-09JG-00-1

SN1F-16CJ-2-10JG-00-1

SN1F-16CJ-2-11JG-00-1

SN1F-16CJ-2-12JG-00-1

What is the precaution while working in the cockpit?

Do not meddle with the flip-up pitot tube

Ensure the canopy is in the midway position so that the canopy field brake circuit take effect

Place your hands/arms on the canopy sill (longeron)

Ensure the recovery sequencer indicator is red, signifying an operational condition

What additional precautions must be taken while entering and exiting the MLU cockpit?

Check for presence of CRS knob on CPD and no damage during cockpit entry and exit

Check for presence of BARO knob and CPD and no damage during cockpit entry and exit

Check for presence of CRS and BARO knob and CPD and no damage during cockpit entry and exit

None of the above

Why is it important to ensure Anti-G hose is properly positioned and secured before operating the seat adjustment switch?

To prevent Anti-G connector being damaged if crushed between seat and structure

To prevent damage to Side Stick Controller

To ensure that seat is free of object and ideal for resting

To prevent damage to Canopy Actuator Release Bolt

When external power is applied, what other Ground Support Equipment (GSE) is required ?

Air-conditioning unit

Hydraulic Mill

Nitrogen Cart

Oxygen Trolley

Where are the safety pins to make the F16 cockpit Egress System safe?

Inside the canvas bag located behind the FWD LEFT SIDE seat

Inside the canvas bag located behind the FWD RIGHT SIDE seat

Inside the canvas bag located behind the AFT seat

Inside the storage bag in the fuselage

How do you unlock the Canopy Lock Handle from the outside of the aircraft?

Using a thin rod to deflect the handle

Removes the access plug first and use a thin rod to deflect the handle

Rotates the access plug in the counter-clockwise direction

Rotate the manual drive to the OPEN position

When aircraft battery is power is low, do not attempt to open canopy using the canopy switch to prevent damage to the _________

Canopy

Aircraft battery

Canopy Linkage

Canopy Actuator

Initiating the external jettison handle on either side of the aircraft will _______.

Jettison the canopy alone

Jettison the canopy followed by seat ejection

Activate the H-70 Hydrazine

Nothing happens as both left and right hand canopy jettison handles must be pulled simultaneously

Where are the most of the INITIATORS (explosives) located in the Egress system?

Seat

Seat Support

Canopy

Longeron

The Emergency Oxygen Bottle can be operated manually by _________ .

Emergency release handle

Ejection control handle

A green ring stowed on the seat

A firing handle located at the front of the seat

When entering and exiting the MLU cockpit,

We can use the Magnetic Transmitting device as support when entering only

Do not use the Magnetic Transmitting device as support

We can use the Magnetic Transmitting device as support when exiting only

We can use the Magnetic Transmitting device as support for both entering and exiting

Before entering the cockpit, you discovered that the Recovery Sequencer Indicator is RED (red pin protruding), what should you carry out?

Depress the pin to make it safe

Wait for it to turn WHITE

Inform Egress personnel and/or PDS/Hangar I/C immediately

Inform your respective I/C

Which of the followings should be observed & comply prior to entry to cockpit?

When position crew entry ladder for forward cockpit, avoid contact with throttle

Use the body position handles on canopy to assist in entering or exiting cockpit

Seat should can used as a step to enter or exit cockpit

All of the above

On the ejection control safety lever, one must ensure that the control rod connecting rivet is properly installed because if the rivet is broken or missing, _____ .

The ejection control safety lever will not be able to place in the up (safe) position

The ejection control safety lever will not be able to place in the down (armed) position

The seat might be in the armed position even if the ejection control safety lever is in the up (safe) position

The safety pin will not be able to insert into the ejection control lever

Before any maintenance is carried out in the cockpit, what must you verify?

Ensure recovery sequencer indicator is RED

Safety pins are installed in the seat

Safety pins are installed in the external canopy jettison system

No check is required,

When the SMS switch is put to 'OFF' position, power is cut off to _____ .

All Avionics system

All Flight Control system

All Weapon system

All Electrical system

Before applying hydraulic power to the aircraft, you must _____ .

Ensure landing gear handle in the 'up' position

Ensure speedbrake switch at the forward or 'close' position

Ensure personnel is under the moving flight control surfaces

Ensure anticollision light is on to warn others

Care must be exercise to ensure that the seat height adjustment motor is not in the continuous operation for _____ .

15 seconds without 5 minutes rest

5 minutes without 30 minutes rest

2 minutes without 5 minutes rest

10 minutes maximum

If the internal switch is left in the 'up' position, what happens when you try to close the canopy using the external canopy switch?

The canopy will not close

The canopy will remain closed

The canopy will close and then open again

The canopy will close provided the canopy lock handle is in the lock

What will happen if you try to close the canopy externally and the internal canopy switch is placed in the 'up' position ?

The canopy will still close

The canopy will close and then open again

Nothing happens as both switches contradict each other

Canopy actuator will burnout

All emergency handles and switches in the F16 cockpit are painted in _____ .

Black and Yellow Stripes

Black and White Stripes

Red and White Stripes

Yellow and Red Stripes

Why is it so critical to ensure all rings, watches, etc. Are removed when working side or around the cockpit areas?

FOD hazards

Damage to seat

Damage to seat support

Damage to canopy actuator

Which of the following statements is incorrect in regards to cockpit safety?

While entering into the cockpit, do not use the seat pitot tube to hold steady yourself

Empty overall pocket and remove and FOD hazards, e.g. rings, watches, chains etc.

Ensure crew entry ladder is placed correctly at the appropriate position prior climbing up

Mechanical crank up the canopy using 3/4" ratchet

What will happen if two sensors of the UWARS are shorted?

Drain off the battery of the UWARS release system

Cause damage to the sensors

Activation of the UWARS release system

Nothing will happen

Whenever external power is applied, what precautions(s) must be taken before main power switch is selected to 'main power'?

JFS start switch at 'ON' position

Landing Gear Handle in 'down' position

EPU mode switch at 'ON' position with upper half of the switch guard closed

MASTER ARM switch to 'MASTER ARM'

To operate the canopy using the external canopy switch, what must be the position of the canopy lock handle?

Unlocked

Lock

Mid-Way

Any position

COCKPIT GUIDELINE

More Surveys