Design RuleBook
Design RuleBook Quiz
Test your knowledge on the essential design rules and standards in engineering! This quiz covers various aspects of vehicle design, safety regulations, and structural integrity.
Challenge yourself with questions such as:
- True or False statements regarding safety standards
- Multiple-choice questions on material specifications
- Requirements for vehicle components and structures
Which of these is TRUE?
The load applicator must have a radius of 60 mm
The laminates encapsulating the front hoop must overlap by minimum 25 mm on each side
If the panel core thickness is 5 mm then the test panel must measure 250 mm x 275 mm
During IA test 50 mm clearance forward of the AIP is a must
Which of these is FALSE?
Any harness attachment to a monocoque must use two 10 mm metric grade 8.8 bolt or two 8 mm metric grade 8.8 bolts
All of these
The front hoop bracing structure must be attached no lower than 50 mm below the top-most surface of the front hoop
All aerodynamic devices lower than 500 mm from the ground and further rearward than the front axle, must not be wider than a vertical plane touching the most outboard point of the front and rear tire
If multiple panels are used for floor closeout, the gaps between panels must
Be less than 0.3 mm
Be less than 4 mm
Exceed 3 mm
Be at least 0.4 cm
Which of the following is TRUE?
Reflective foil or tape cannot be used for heat insulation
Floor closeout must extend from front bulkhead to the main hoop
None of these
No part of the primary structure may lie below 20 mm of the endpoints of the roll hoops
Multiple panels used to form firewall must overlap
At least 0.5 cm
At most 5 mm
At least 3 mm
At most 0.3 cm
Pass-throughs for wiring, cables, etc. Are permitted if grommets are used to seal the pass- through in firewall
False
True
The two layers of tractive system firewall can be made of aluminium and CFRP
True
False
All vehicle controls must be operated from inside the cockpit without any part of the driver being outside the vertical planes coincident to the outermost surface of the side impact structure
True
False
Minimum width of antisubmarine straps is
60 mm
55 mm
50 mm
75 mm
Reclined seat back angle is 30° with respect to the vertical line
True
False
Which of the following is TRUE for shoulder straps?
Y type strap configuration is allowed
H type strap configuration is allowed
None of these
All of these
Which of the following is FALSE?
All aerodynamic devices must not extend further rearward than 250 mm from the rearmost part of the rear tires
Minimum area moment of inertia for driver's restraint harness attachment is 8409 mm^4
If AIP is welded to the front bulkhead, it must extend at least to the centerline of the front bulkhead tubing in all directions
Head restraint must have minimum height and width of 150 mm
Bolted attachment points between two parts must be able to carry a load of
30 N
20 kN
20 N
30 kN
All threaded critical fasteners
Must be 4 mm metric grade 8.8 except OEM parts
Can be ISO 4017, ISO 4014 and DIN7379
Can be DIN7984 and DIN980
All of these
Which of the following is TRUE?
The fire extinguishers must have a minimum firefighting capacity of 0.9 kg
Stroke width and spacing between vehicle number must be at least 30 mm
The front hoop shouldn't be aluminium welded structure
None of these
{"name":"Design RuleBook", "url":"https://www.quiz-maker.com/QPREVIEW","txt":"Test your knowledge on the essential design rules and standards in engineering! This quiz covers various aspects of vehicle design, safety regulations, and structural integrity.Challenge yourself with questions such as:True or False statements regarding safety standardsMultiple-choice questions on material specificationsRequirements for vehicle components and structures","img":"https:/images/course8.png"}